R125

References

Equation of State

Eric W. Lemmon and Richard T Jacobsen. A New Functional Form and New Fitting Techniques for Equations of State with Application to Pentafluoroethane (HFC-125). J. Phys. Chem. Ref. Data, 34(1):69–108, 2005. doi:10.1063/1.1797813.

Thermal Conductivity

Richard A. Perkins and Marcia L. Huber. Measurement and Correlation of the Thermal Conductivity of Pentafluoroethane (R125) from 190 K to 512 K at Pressures to 70 MPa. J. Chem. Eng. Data, 51:898–904, 2006. doi:10.1021/je050372t.

Viscosity

Marcia L. Huber and Arno Laesecke. Correlation for the Viscosity of Pentafluoroethane (R125) from the Triple Point to 500 K at Pressures up to 60 MPa. Ind. Eng. Chem. Res., 45:4447–4453, 2006. doi:10.1021/ie051367l.

Surface Tension

A. Mulero, I. Cachadiña, and M. I. Parra. Recommended Correlations for the Surface Tension of Common Fluids. J. Phys. Chem. Ref. Data, 41(4):043105–1:13, 2012. doi:10.1063/1.4768782.

Fluid Information

Parameter, Value

General

Molar mass [kg/mol]

0.1200214

CAS number

354-33-6

ASHRAE class

UNKNOWN

Formula

\(C_{2}F_{5}H\)

Acentric factor

0.3052

InChI

InChI=1S/C2HF5/c3-1(4)2(5,6)7/h1H

InChIKey

GTLACDSXYULKMZ-UHFFFAOYSA-N

SMILES

C(C(F)(F)F)(F)F

ChemSpider ID

9256

2D image

http://www.chemspider.com/ImagesHandler.ashx?id=9256

Limits

Maximum temperature [K]

500.0

Maximum pressure [Pa]

60000000.0

Triple point

Triple point temperature [K]

172.52

Triple point pressure [Pa]

2914.046009255466

Critical point

Critical point temperature [K]

339.173

Critical point density [kg/m3]

573.5822706

Critical point density [mol/m3]

4779.0

Critical point pressure [Pa]

3617700.0

REFPROP Validation Data

Note

This figure compares the results generated from CoolProp and those generated from REFPROP. They are all results obtained in the form \(Y(T,\rho)\), where \(Y\) is the parameter of interest and which for all EOS is a direct evaluation of the EOS

You can download the script that generated the following figure here: (link to script), right-click the link and then save as… or the equivalent in your browser. You can also download this figure as a PDF.

../../_images/R125.png

Consistency Plots

The following figure shows all the flash routines that are available for this fluid. A red + is a failure of the flash routine, a black dot is a success. Hopefully you will only see black dots. The red curve is the maximum temperature curve, and the blue curve is the melting line if one is available for the fluid.

In this figure, we start off with a state point given by T,P and then we calculate each of the other possible output pairs in turn, and then try to re-calculate T,P from the new input pair. If we don’t arrive back at the original T,P values, there is a problem in the flash routine in CoolProp. For more information on how these figures were generated, see CoolProp.Plots.ConsistencyPlots

Note

You can download the script that generated the following figure here: (link to script), right-click the link and then save as… or the equivalent in your browser. You can also download this figure as a PDF.

../../_images/R1251.png